Infeed table made of tubular steel, length mm 2500
Poly-v belts drive on all spindles, they bear the best efficiency of motors powers
Independent motor unit on each work unit
Upper traverse equipped with motorized vertical movement, with drive rollers and pressing devices adjustable simultaneously with the upper spindle for higher speed and easier setup
Feed system by means of universal joints, double back chain and speed variator with inverter
Upper drive supported by double column
Drive by means of 4 gear wheels and upper rubber wheels in outfeed
Blowers on the table to optimize wood sliding
Vertical lh spindle adjustable simultaneously with pressure unit and outfeed guide, for higher speed and easier setup
Pre-straightening system on the rh side by means of pre-grooving cutter head (upon request) mounted on planer spindle
Decimal precision reading 0,1 mm of 3° – 4° – 5° – 6° spindle displacements
Quick tool adjusting system on 2° – 3° – 4° unit
Possibility to mount cutters on 2° – 3° – 4° spindle up to a max. diameter of 200mm and a min. diameter of 110mm (max. moulding diameter 160mm)
Axial rh and lh router adjustment from 0mm up to -90mm by means of controls situated on the machine front
Radial adjustment 2° spindle by 35mm
Radial pressing device adjustment 3° unit compared with the spindle by 35 mm (to compensate diam.)
Axial adjustment of 4° spindle by 40mm
Radial adjustment of 4° spindle by 35mm (for diameter compensation)
Max tool diameter: 200mm over the worktable and 160mm under the worktable
Pneumatic pre-planer roller with exclusion on control panel
Pneumatic pressure on drive units
Manual lubrication of worktable
Direct motor start by light push-buttons from control panel
Soundproof protection cabin complete with safety micro-switches
Control panel with magnetothermal protection
Lockable main switch
2pcs emergency push-buttons
Low voltage auxiliary circuit
Service keys
Hood room light
Mobile console with control panel to simplify the operator set-up and start of production cycle
UPON REQUEST
Set of tools: n. 02 planing cutter heads 190 x 125 x 40; n. 02 planing cutter heads 250 x 125 x 40; n. 01 pre-grooving cutter head 12 x 145 x 40 (throwaway cutters); n. 01 knife setting gouge
Spyral set of tools: n. 02 planing cutter heads 190 x 125 x 40; n. 02 planing cutter heads 270 x 125 x 40; n. 01 pre-grooving cutter head 12 x 145 x 40
Planing cutter head 270 x 125 x 40
Planing cutter head 190 x 125 x 40
UL/CSA rule
Volt 220 and special voltages
60 hz
Automatic worktable lubrication
Centralized lubrication of guides by means of hand-operated pump
Centralized lubric.guides by means of pump operated from control panel
Central.lubric. vertical spindles by means of hand-operated pump
Central.lubric.vertical sp. by means of pump operated from control panel
Automatic air and oil automizer
Additional feed wheel extension shaft in front of the lh vertical spindle, complete with gear wheel 45mm
Additional feeding device for short piece (mounted in front of rh sp.): min. working length of single work-piece: 590mm; min. pushing working length with short pieces device: 300mm
Add. gear wheel thickness 18mm
Add. gear wheel thickness 45mm
Add. rubber wheel thickness 20mm
Add. rubber wheel thickness 50mm
Motorized adjustment of 3rd unit (working width) complete with electrical motor and push-buttons (opening/closing) and decimal adjustment by means of 1 electronic value display with leds
Electronic display with leds for height work measurement
Electronic control 2 axes: automatic control of left vertical spindle and top horizontal spindle positioning. Automatic start of all motors included feeding motor. 7" PLC colour display. Min. working height 10mm. Axial RH and LH spindle adjustment - 80mm instead of -90mm
Electronic control 4 axes: automatic control of right vertical spindle in vertical (Z axis) and left vertical spindle in vertical and horizontal (Z and Y axis) and top horizontal spindle (Z axis) positioning. Automatic start of all motors included feeding motor. 7" PLC colour display. Min. working height 10mm. Axial RH and LH spindle adjustment -80mm instead of -90mm
Electronic control 5 axes with automatic start of all motors included feeding motor. 7" PLC colour display. Min. working height 10mm. Axial RH and LH spindle adjustment -80mm instead of -90mm
Controllo elettronico 5 assi : avviamento automatico dei motori compreso l'avanzamento. Monitor 7" a colori touch. Altezza minima di lavoro 10mm. Regolazione assiale toupie dx e sx 80mm invece di 90mm
Automatic workpiece width searching device obtained by means of automatic displacement of 3rd spindle; it offers the possibility to work in sequence panels with different widths. The system is driven by ball-recirculating screw which can be disconnected by means of control on control panel. With this option add at least plc 2 ax
10" monitor colour display for PLC
15" monitor colour display for PLC
Automatic pre-planer exclusion device at the first drive group entry
Speed variator with inverter kW3
Pre-grooving cutter head (throwaway cutters)
Knife setting gauge
Splitted pneumatic pressure on drive rollers
Motor 1st planer kW 5,5 (HP 7,5)
Motor 1st planer kW 7,5 (HP 10) Automatic star/delta start is compulsory
Motor rh spindle kW 5,5 (HP 7,5)
Motor 1st planer kW 7,5 (HP 10) Automatic star/delta start is compulsory
Motor lh spindle kW 5,5 (HP 7,5)
Motor lh spindle kW 7,5 (HP 10)
Motor top horizontal spindle kW 7,5 (HP 10) Automatic star/delta start is compulsory
Motor top horizontal spindle kW 9 (HP 12) Automatic star/delta start is compulsory
Motor 2nd top horizontal spindle kW 5,5 (HP 7,5)
Motor 2nd top horizontal spindle kW 7,5 (HP 10) Automatic star/delta start is compulsory
Motor 2nd top horizontal spindle kW 9 (HP12) Automatic star/delta start is compulsory
Motor 2nd bottom horizontal spindle KW 5,5 (HP 7,5)
Motor 2nd bottom horizontal spindle KW 7,5 (HP 10) Automatic star/delta start is compulsory
Motor 2nd bottom horizontal spindle kW 9 (HP 12) Automatic star/delta start is compulsory
Automatic star/delta start for the single tool motor It is compulsory on motors HP 10 / HP 12
Kit of rings composed by rings of differents thickn.for an overall length 200mm
Min. working width 15mm with no. 2 steel rollers thickness 10mm
Feed system on infeed table to feeds work-pieces into the machining area
