Infeed table made of tubular steel, length mm 2300
Poly-v belts drive on all spindles, they bear the best efficiency of motors powers
Independent motor unit on each work unit
Upper traverse equipped with motorized vertical movement, with drive rollers and pressing devices adjustable simultaneously with the upper spindle for higher speed and easier setup
Feeding system by means of universal joints,double back chain and speed variator with inverter
Drive by means of 4 gear wheels and 1 rubber wheel in outfeed
Blowers on the table to optimize wood sliding
Vertical lh spindle adjustable simultaneously with pressure unit and outfeed guide, for higher speed and easier setup
Pre-straightening system on the rh side by means of pre-grooving cutter head (upon request) mounted on planer spindle
Decimal precision reading 0,1 mm of 3° – 4° – 5° spindle displacements
Quick tool adjusting system on 2° – 3° – 4° – 5° unit
Possibility to mount cutters on 2° – 3° – 4° – 5° spindle up to a max. diameter of 180mm and a min. diameter of 110mm (max. moulding diameter 160mm)
Radial adjustment 2° – 3° – 4° spindle by 35mm by means of controls situated on machine front
Vertical router travel -40mm under the worktable with max cutter diameter 160mm
Pneumatic pre-planer roller with exclusion on control panel
Pneumatic pressure on drive units
Manual worktable lubrication
Direct motor start by light push-buttons from control panel
Soundproof protection cabin complete with safety micro-switches
Control panel with magnetothermal protection
Lockable main switch
2pcs emergency push-buttons
Low voltage auxiliary circuit
Service keys
Hood room light
UPON REQUEST
Set of tools: n. 02 planing cutter heads 130 x 125 x 40; n. 02 planing cutter heads 230 x 125 x 40; n. 01 pre-grooving cutter head 12 x 145 x 40 (throwaway cutters); n. 01 knife setting gouge
Spyral set of tools: n. 02 planing cutter heads 130 x 125 x 40; n. 02 planing cutter heads 230 x 125 x 40; n. 01 pre-grooving cutter head 12 x 145 x 40
Pre-grooving cutter head (throwaway cutters)
Planing cutter head 230 x 125 x 40
Planing cutter head 130 x 125 x 40
Knife setting gauge
UL/CSA rule
Volt 220 and special voltages
Automatic worktable lubrication
Centralized lubrication of guides by means of hand-operated pump
Centralized lubric.guides by means of pump operated from control panel
Automatic air and oil automizer
Additional feed wheel extension shaft in front of the lh vertical spindle, complete with gear wheel 45mm
Additional feeding device for short piece (mounted in front of rh sp.): min. working length of single work-piece: 400mm; min. pushing working length with short pieces device: 200mm (P230/4 PLUS)
Additional feeding device for short piece (mounted in front of rh sp.): min. working length of single work-piece: 490mm; min. pushing working length with short pieces device: 300mm (P230/5U PLUS)
Add. gear wheel thickness 18mm
Add. gear wheel thickness 45mm
Add. rubber wheel thickness 20mm
Add. rubber wheel thickness 50mm
Motorized adjustment of 3rd unit (working width) complete with electrical motor and push-buttons (opening/closing) and decimal adjustment by means of 1 electronic value display with leds
Electronic display with leds for height work measurement
Electronic control 2 axes: automatic control of left vertical spindle and top horizontal spindle positioning. Automatic start of all motors included feeding motor. 7" PLC colour display
Automatic device search for the width of the piece obtained by automatic movement of the 3rd spindle; it offers the possibility to process in succession the pieces of different widths between them. The system is moved by a ball screw that can be disengaged by control from the electrical panel. With this optional it is necessary to combine the PLC option with two or more controlled axes
Automatic pre-planer exclusion device at the first drive group entry
10" monitor colour display for PLC
15" monitor colour display for PLC
Speed variator with inverter kW 2,2
Motor 1st planer kW 5,5 (HP 7,5)
Motor 1st planer kW 7,5 (HP 10)
Motor rh spindle kW 5,5 (HP 7,5)
Motor lh spindle kW 5,5 (HP 7,5)
Motor top horizontal spindle kW 7,5 (HP10)
Motor universal kW 5,5 (HP 7,5) (P230/5U PLUS)
Motor universal kW 7,5 (HP 10) (P230/5U PLUS)
Kit of rings composed by rings of differents thickn.for an overall length 200mm
Min. working width 15mm with no. 2 steel rollers thickness 10mm